2.1.1_IA_Medium LITHIUM METAL CELLS (including lithium alloy cells) Medium cells regulated UN 3090 Applies to: Lithiummetal cells with a lithiummetal content in excess of 1 g/cell but less than 5 g/cell IATA Only: Lithiummetal cells with a lithiummetal content not exceeding 1 g/cell transported in quantities that exceed the allowance permitted in § 2.1.1_IB UN No., Proper Shipping Name UN 3090, LITHIUM METAL BATTERIES Class 9 Packing Group Not assigned Hazard Label Labels must be in the form of a square set at an angle of 45° (diamond-shaped) with minimum dimensions of 100 mm by 100 mm; except for air transport mode, labels dimensions may be reduced not less then 30mm by 30mm on small packages. • They must have a line 5 mm inside the edge and running parallel with it. Prerequisite • Cells must meet the General Requirements of §173.185(a) in particular the test requirements Specific Requirements • Unless shipped via road/rail, each cell incorporates a safety venting device or is designed to preclude a violent rupture under normal conditions of carriage; • Unless shipped via road/rail, each cell is equipped with an effective means of preventing external short circuits Transport mode Road Marine Air Passenger Aircraft Cargo Packing instructions 173.185(c) P903 PI 968 section IA • Cells must be protected against short circuit, including protection against contact with conductive materials within the same packaging which could cause a short circuit. • Cells must be packed so that are protected against damage caused by the movement or placement of the cells within the packaging • lithiummetal cells must be placed in inner packagings that completely enclose the cell, then placed in an outer packaging. • Use only approved packaging conforming to Packing Group II performance level. Forbidden • lithium metal cells must be placed in inner packagings that completely enclose the cell, then placed in an outer packaging. • complete package must be approved Packing Group II performance level • Restriction: see § 1.9.3 Packagings Strong outer packaging, it must be capable of withstanding a 1.2 m drop test in any orientation without damage to cells contained therein, without shifting of the contents so as to allow cell to cell contact and without release of contents. Drums (1A2, 1B2, 1N2, 1H2, 1D, 1G); Boxes (4A, 4B, 4N, 4C1, 4C2, 4D, 4F, 4G, 4H1, 4H2) Jerricans (3A2, 3B2, 3H2). Drums (1A2, 1B2, 1N2, 1H2, 1D, 1G); Boxes (4A, 4B, 4N, 4C1, 4C2, 4D, 4F, 4G, 4H2) Jerricans (3A2, 3B2, 3H2). Cells ≥ 12 kg (gross) with a strong, impact resistant outer casing Not required UN approved packagings for cells, or assemblies of such cells, when packed in strong outer packagings or protective enclosures (e.g., fully enclosed or wooden slatted crates) Allowed transport on Pallets or other handling devices. Cells must be secured to prevent inadvertent movement, and the terminals must not support the weight of other superimposed elements Outer packagings or protective enclosures approved by the appropriate authority of the State of origin. A copy of the document of approval must accompany the consignment. Large Packaging 173.185(b)(6) LP903 Rigid Large packagings, conforming to the packing group II performance level, are authorized for a single battery.: • steel (50A); • aluminium (50B); metal other than steel or aluminium (50N); • rigid plastics (50H); • natural wood (50C); • plywood (50D); • reconstituted wood (50F); • rigid fibreboard (50G). Weight limit 30 kg Gross No limit Forbidden 35 kg Net Marking and Labelling of Packages Li Batt Mark minimum dimensions: 100 × 100 mm, for small packages reduced to 100 mm × 70 mm CAO dimensions: 120 mm x 110 mm UN 3090, LITHIUM METAL BATTERIES UN 3090 LITHIUM METAL BATTERIES Full Name and Address of the shipper and the consignee Net weight (kg) Minimum dimension 1 s 2 : 0 × 110 mm Overpack: OVERPACK + same labels as above OVERPACK + same labels as above OVERPACK + same labels as above Restriction: see § 1.9.3 Documents Transport document is not required Transport document Shipper’s Declaration International Transport Regulations 24 Small Excepted Lithium battery mark Applicable until 31.12.2026 Applicable from 1.1.2023 Lithium battery mark A rectangle or a square of minimum dimensions 100 x 100 mm and the minimum width of the hatching shall be 5 mm. The symbol shall be black, the hatching shall be red. If the size of the package so requires, the dimensions may be reduced to not less then 100 x 70 high. The rectangular mark 120 x 110 mm dimension may continue to be used. For IATA DGR, the character of the UN numbers shall be at least 12 mm height Handling Labels Cargo Aircraft Only for IATA DGR Minimum dimensions 120 x 110 mm Lithium batteries – Forbidden for transport aboard aircraft and vessel 48 Copyright © www.batteriestransport.org
RkJQdWJsaXNoZXIy MjQwNg==